OpenFlash Tablet OFTCODE List

Created by Anthony Cardinale, Modified on Sat, 13 Jun, 2020 at 2:51 PM by Anthony Cardinale

OFT Code	Message	Solution
10001	Protocol file not found.	Allow your OFT to fully update via OpenFlash Manager
10002	Protocol file corrupted.	Allow your OFT to fully update via OpenFlash Manager
10003	An error occurred while reading data from your ECU. Check cable connections, ignition switch position,\|then try again.	The OFT did not receive the proper communication messages while trying to read the ECU. The ECU may be locked by another tuning system.
10004	ECU number mismatch! ECU write denied!	The OFT is not installed onto the car you’re attempting to program a tune file onto.
10005	Tuning file corrupt!	Contact OpenFlash Performance via email.
10006	Impossible to find message number.	Contact OpenFlash Performance via email.
10007	OFT(x) out of sync. ECU write denied!	Contact OpenFlash Performance via email.
10008	Configuration file missing or corrupted. Please update OFT(x).	Contact OpenFlash Performance via email.
10009	Vehicle list missing. Please update OFT(x).	Allow your OFT to fully update via OpenFlash Manager
10010	An error occurred while writing the ECU. Check cable connections, ignition switch position, then try again.	The OFT may have lost communication with your ECU while writing a tune file. CHeck battery voltage, inspect the OBD connector at the vehicle and OFT, and check your ignition switch position; then try again.
10011	ECU communication error. Check cable connections, ignition switch position, and try again.	The OFT did not receive the proper communication messages while trying to interact with the ECU. The ECU may be locked by another tuning system, or damaged. Check the ignition switch position. Ensure the OBD cable connections are secure/seated at the vehicle and OFT. Check for proper battery voltage = 12.6v or more. Try again.
10012	Language file missing. Please update OFT(x) using OpenFlash Manager.	Contact OpenFlash Performance via email.
10013	Tune file mismatch. ECU write denied!	The tune file you’re trying to program is not compatible with your ECU. Contact OpenFlash Performance via email.
10014	OFT(x) data corrupt.	Contact OpenFlash Performance via email.
10015	ECU identification error. Check cable connections, ignition switch position, then try again.	The OFT did not receive the proper communication messages while trying to interact with the ECU. The ECU may be locked by another tuning system, or damaged. Check the ignition switch position. Ensure the OBD cable connections are secure/seated at the vehicle and OFT. Check for proper battery voltage = 12.6v or more. Try again.
10016	Unknown ECU! This ECU number is not recognized by OFT(x).	Contact OpenFlash Performance via email.
10017	No ECU response. Check cable connections, ignition switch position, and try again.	The ignition switch may not be in the IGNITION position The OBD cable is not seated in the OFT or vehicle properly The OBD cable is damaged
10018	Reached maximum of 14 channels.	Only 14 signals can be logged/viewed at one time.
10019	Tune file spaces are empty! ECU write denied!	Load tune files to your OFT.
10020	ECU was READ successfully! Mod-file not found for this calibration code. Upload tune files using Openflash Manager.	Your ECU has been read, but you’ll need to manually load tune files to your OFT using OpenFlash Manager.
10021	Update this OFT(x)'s\|template file.	Download an updated template file from support.openflashtablet.com, and load it to your OFT using OpenFlash Manager.
12016	Screen re-calibration failed. Try again, using a stylus.	You must use a pointed stylus (not a stylus with a blunt/squishy tip). Try using a slightly dull pencil. Press in the exact center of the green squares as they appear.
12017	OFT(x) out of date. Please update your device with OpenFlash Manager.	Allow your OFT to fully update via OpenFlash Manager
12019	Function not available.	Contact OpenFlash Performance via email.
12020	Un-supported ECU.	Contact OpenFlash Performance via email.
12021	Calibration code not recognized.	Your ECU may have a new calibration code that is not currently in our database. Please contact OpenFlash Performance via email.